Resistors

From Amateur-radio-wiki
(Redirected from Resistance)
Jump to: navigation, search

Resistance and Resistivity

Resistance (R) is the measure of how much an object - a resistor - opposes the flow of electric current. The resistance of an object is measured in Ohms (<math>\Omega</math>)

Resistivity (<math>\Rho</math>) is a measure of how strongly a material opposes the flow of electric current. Resistivity is measured in ohm metres (<math>\Omega</math>m). Related wiki page: table of resistivities

The relationship between resistance and resistivity is:

<math>R = {l \cdot \rho \over A} \,</math>

where

<math>l</math> is the length of the object
<math>A</math> is the cross sectional area of the object (assuming constant), and
<math>\rho</math> is the resistivity of the material
<math>R</math> is the resistance

Resistors

A resistor is a passive electrical device that has been manufactured specifically to add resistance to a circuit, to effect a voltage drop.

The mathematical equation that describes the relationship between resistanece, voltage drop and current through a resistor is known as Ohms Law

<math>I = \frac{V}{R}</math>

where

"I" is the current in amperes,
"V" is the potential difference between the ends of the resistor in volts, and
"R" is the resistance of the resistor, measured in ohms

Resistor circuit symbols

Vk4yeh resistor symbols.jpg

Resistors in series and parallel

Vk4yeh resistors series.jpg

Total resistance in a series circuit: <math> R_\mathrm{T} = R_1 + R_2 + R_3 </math>

Vk4yeh resistors parallel.jpg

Total resistance in a parallel circuit: <math> \frac{1}{R_\mathrm{T}} = \frac{1}{R_1} + \frac{1}{R_2}+ \frac{1}{R_3} </math>

<math> R_\mathrm{T} = R_1 \| R_2 = {R_1 R_2 \over R_1 + R_2} </math>

Resistor colour bands

The resistance of a resistor is coded into a series of coloured bands along its length:

  • band A is first significant figure of component value
  • band B is the second significant figure
  • band C is the decimal multiplier
  • band D if present, indicates tolerance of value in percent (no color means 20%)
Error creating thumbnail: Unable to save thumbnail to destination


Color Band A Band B Band C (multiplier) Band D (tolerance) Temp. Coefficient
Black 0 0 ×100    
Brown 1 1 ×101 ±1% (F) 100 ppm
Red 2 2 ×102 ±2% (G) 50 ppm
Orange 3 3 ×103   15 ppm
Yellow 4 4 ×104   25 ppm
Green 5 5 ×105 ±0.5% (D)  
Blue 6 6 ×106 ±0.25% (C)  
Violet 7 7 ×107 ±0.1% (B)  
Gray 8 8 ×108 ±0.05% (A)  
White 9 9 ×109    
Gold     ×10-1 ±5% (J)  
Silver     ×10-2 ±10% (K)  
None       ±20% (M)  

Using the colour code

For example a resistor with bands Brown Black Orange Blue would have resistance 10×103 <math>\Omega</math> (10 000<math>\Omega</math>) with a tolerance of ±0.25%

Resistor types

Carbon composition

Carbon composition resistors consist of a solid cylindrical resistive element made from a mixture of finely ground carbon and an insulating material. The mixture is held together by a resin, and wires are either embedded in the ends, or a thin metal cap and wire is attached to each end. The resistance is determined by the ratio of the powdered ceramic and the carbon. Higher concentrations of carbon result in lower resistance. These resistors are generally of high tolerance.

Carbon film

A spiral is used to increase the length and decrease the width of the film, which increases the resistance. Varying spiral shapes are used to create a variety of resistances.

Thick and thin film

Most SMD (Surface Mount Device) resistors are of this type. The principal difference between "thin film" and "thick film resistors" is how the film is applied to the cylinder (axial resistors) or the surface (SMD resistors). In thick film resistors the "film" is applied using traditional screen-printing technology.

Thin film resistors are made by sputtering the resistive material onto the surface of the resistor. The thin film is then etched to attain the desired resistance.They are then trimmed to an accurate value by abrasive or laser trimming.

By contrast, thick film resistors, may use the same conductive ceramics as thin film resistors, but they are mixed with powdered glass, and a liquid so that the composite can be screen-printed . This composite of glass and conductive ceramic (cermet) material is baked) in an oven at about 850 °C.

Metal film

A common type of axial resistor today is referred to as a metal-film resistor. MELF (Metal Electrode Leadless Face) resistors often use the same technology, but are a cylindrically shaped resistor designed for surface mounting. [Note that other types of resistors, eg carbon composition, are also available in "MELF" packages].

Metal film resistors are usually coated with nickel chromium (NiCr), but might be coated with any of the cermet materials listed above for thin film resistors.

Wirewound

Wirewound resistors are commonly made by winding a metal wire around a ceramic, plastic, or fiberglass core. The ends of the wire are soldered or welded to two caps, attached to the ends of the core. The assembly is protected with a layer of paint, molded plastic, or an enamel coating baked at high temperature. The wire leads are usually between 0.6 and 0.8 mm in diameter and tinned for ease of soldering. For higher power wirewound resistors, either a ceramic outer case or an aluminium outer case on top of an insulating layer is used. The aluminium cased types are designed to be attached to a heatsink to dissipate the heat; the rated power is dependant on being used with a suitable heatsink, e.g., a 50 W power rated resistor will overheat at around one fifth of the power dissipation if not used with a heatsink.

Because wirewound resistors are coils they have more inductance than other types of resistor, although this property can be minimized by winding the wire in sections with alternately reversed direction.

Foil resistor

Foil resistors have had the best precision and stability ever since they were introduced in 1958.

Resistor Circuits

Voltage Divider

Perhaps the most common use for resistors in a circuit is as a voltage divider:

Voltage divider.jpg

In this configuration, <math> V_{out} = \frac {R_2 \times V_{in}}{R_1+R_2} </math>

See also


External link

Electronic Theory
Physical quantities Current * Gain * Impedance * Power * Q of a circuit * Radiated Power Measurement * Reactance* Resistivity * Resonance * Voltage
Components Baluns * Bipolar-Junction Transistors * Capacitors * Diodes * Inductors* Lasers * Microphones * Resistors * Transformers * Wire
Circuits Attenuators * Digital Signal Processing (DSP) * Dummy load * Filters * LC filters * Power Supply Design * Rectifier Circuits
Design Amplifier Design * Oscillator Design
Electromagnetic Waves Relative power (Decibels) * Harmonics * Interference and BPL